Note: Always perform the maintenance steps below with the printer powered off and the labels and ribbon removed from the printer.
The i3311 printer includes a cleaning kit which has a plastic bottle, lint free swabs, and a cutter blade scraper. If the cleaning kit was lost or disposed of, a generic lint free swab and a spray bottle can be used as a substitute.

Recommended Cleaning Supplies
- Compressed Air
- Lint-free Cloth
- Isopropyl Alcohol (90% recommended).
- Safety Glasses
Areas to Clean on the i3311
Cleaning Residue and Dust
Whenever performing any maintenance on the printer, you should also clean any adhesive residue or dust.

- Power off the printer by flipping the power switch on the back.
- Remove the label and ink ribbon rolls from the printer.
- Use compressed air to spray all visible areas inside of the printer to remove accumulated dust.
- Use a cloth moistened with isopropyl alcohol to wipe any remaining dust from inside the printer.
Note: It is recommended to use at least 90% alcohol to insure the liquid dries before it reaches any internal components of the printer.
- Wipe the exterior cover and frame of the printer for dirt and residue.
Cleaning the Screen
- Make sure the printer is powered off.
- Lightly moisten a lint free cloth with isopropyl alcohol, or use a pre-moistened cloth suitable for cleaning a PC screen.
- Gently rub the damp cloth across the screen until all of the residue is removed.
Cleaning the Cutter Blade
- Power off the printer and remove the label roll and ink ribbon if they haven't been removed already.
- Squeeze the two yellow cutter tabs to release the cutter blade. The cutter mechanism and exit chute will slide down behind the printhead door.

- Fill the plastic bottle that is included with the printer with isopropyl alcohol.
- If the cutter blade shows significant adhesive residue, use the cutter cleaning tool in the cleaning kit that is included with the printer to gently scrape the residue off the cutter blade.

- Moisten one of the foam swabs from the cleaning kit with alcohol. Do not allow the alcohol to drip from the swab. If the cleaning kit is no longer available, use any lint free swab as a substitute.
- Clean the cutting blade with moistened swabs until all residue is removed.
Cleaning the Cutter Blade Exit Chute
Note: You should clean the exit chute after cleaning the cutter blade and sensors. The cleaning swab may be damaged when cleaning the exit area.
Recommended Tools
- Industrial Label Printer i3311 Cleaning Kit
- Isopropyl Alcohol
- Make sure the printer is powered off.
- Close the printhead door. It does not need to snap into place.
- Using lint free swabs moistened with isopropyl alcohol, clean the exit chute entrance and exit chute ramp.
Cleaning the Sensors
Recommended Tools
- Industrial Label Printer i3311 Cleaning Kit (if available)
- Isopropyl Alcohol (90%)
- Lint free swabs
The supply and cutter sensors are located inside the printer and may be covered with dust that results from cutting the labels. One of the supply sensors is located under the yellow supply guide, as shown in the picture below. The cutter sensor is located above the cutting blade and is visible only when the cutter is released.
- Make sure the printer is powered off.
- Release the cutter by squeezing the two yellow tabs; the cutter mechanism and exit chute will slide down exposing the cutter sensor.
- With a pre-moistened foam swab, gently wipe the surface of the cutter sensor and the two supply sensors at the locations shown:
- Center die-cut sensor
- Label out/die-cut sensor
- Cutter sensor

- Continue cleaning sensors until all dust or adhesive residue has been removed.
Cleaning the Printhead
Recommended Tools
- Industrial Label Printer i3311 Cleaning Kit
- Isopropyl Alcohol 90%
- Make sure the printer is powered off.
- Fill the plastic bottle from the cleaning kit with isopropyl alcohol.
Note: Do not rub the swab over the bronze-colored area of the printhead. Gently rub across the green and black areas of the printhead to avoid damaging the pixels.

- Continue wiping the printhead until all dust residue has been removed.
- Once all components of the printhead have been cleaned, wait 30 seconds for the alcohol to dry before powering the printer back on.
Replacing the Label Wiper Pad
For printers utilizing continuous label rolls, it is a good idea to replace worn out or dirty wiper arms to prevent dust or adhesion from getting on the labels. See the directions below for replacing the wiper arm.
Brady Part Number: B31-Wiper
- Make sure the printer is powered off.
- Lift and hold the wiper arm while grasping the tab of the wiper insert.
- Pull the tab slightly forward and then slide the wiper insert out of the wiper arm.
- To replace the wiper, insert the lip of the wiper insert into the slot of the wiper arm and slide in until the tab snaps into place
